SiteSide

HS&E test practice: tools and equipment questions

Last updated: · Certloom Learning
Written by Certloom Learning from the pages listed under Sources, checked on the date shown. Not reviewed or endorsed by CITB or CSCS.

Short answer: PUWER 1998 says work equipment must be suitable for the job and the conditions, kept in good repair, guarded where it has dangerous parts and used only by people who are trained. In the test the right answer for a damaged tool is nearly always: stop using it, label it as faulty and report it.

What does PUWER ask for?

RuleWhat it means on site
SuitableThe right tool for the task and the site conditions; a screwdriver is not a lever
MaintainedKept in good repair; a loose hammer head or mushroomed chisel is taken out of use
GuardedGuards stay on dangerous moving parts; never remove one to make the job quicker
TrainingOnly people trained and authorised use the equipment; using one at home does not count

Source: HSE: Provision and Use of Work Equipment Regulations 1998 (PUWER) (checked 2026-11-15)

Worked example: the cracked drill

You pick up a 110 V drill and the plastic casing is cracked. Taping it might hold it together, but it hides the fault and does not make it safe. Under PUWER the tool must be in good repair, and your duty under the Health and Safety at Work Act is to take care and co-operate. So: stop using it, label it as faulty, put it where nobody else will pick it up and tell your supervisor.

Source: HSE: Provision and Use of Work Equipment Regulations 1998 (PUWER); Health and Safety at Work etc. Act 1974 (checked 2026-11-15)

When should you check a tool?

Before each use: casing, cable, plug, switch and guards. Formal inspections and portable appliance tests do not replace your own check, because damage can happen at any time.

What if a workmate removes a guard?

Section 8 of the Health and Safety at Work Act says nobody may interfere with anything provided for safety. Tell them not to use the tool and report it. Keeping your own hands back does not help if a disc bursts.

Source: Health and Safety at Work etc. Act 1974 (checked 2026-11-15)

SiteSide has 1,375 original questions with the English wording on top and full Romanian or Polish underneath, timed 50-question mocks and practice of your mistakes.

Get SiteSide on Google Play Try the free sample

iPhone app coming soon. Until then, practise free on this site.

Free practice questions

9 original practice questions from SiteSide's checked bank of 1,375. Open each one to see the answer and why.

  1. Under PUWER, what must a tool be for the job it is used for?

    1. Bought new within the last twelve months
    2. The lightest model the supplier has in stock
    3. Suitable for the task and the site conditions
    4. Approved in advance by the person who will be using it
    Show answer

    Answer: C. The Provision and Use of Work Equipment Regulations 1998 (PUWER) say work equipment must be suitable for the work and for the conditions where it is used. A new or light tool can still be the wrong tool for the job. If you are not sure a tool is right, ask your supervisor.

    Source: PUWER 1998, regulation 4: Suitability of work equipment, HSE: Provision and Use of Work Equipment Regulations 1998 (PUWER) · b10-001

  2. When should you check a hand-held power tool for obvious damage?

    1. Only when it is first delivered to site
    2. Once a month, when it is formally tested
    3. Only if it starts to make a strange noise
    4. Before each time you use it
    Show answer

    Answer: D. A quick look at the casing, cable, plug and guards before each use finds faults before they hurt someone. Formal tests and inspections are important, but they do not replace the user's own check, because damage can happen at any time. Follow your site rules and report any fault you find.

    Source: HSE: Provision and Use of Work Equipment Regulations 1998 (PUWER), PUWER 1998, regulation 5: Maintenance · b10-002

  3. You pick up a drill and find the plastic casing is cracked. What should you do?

    1. Wrap insulating tape round the crack and carry on
    2. Stop using it, label it as faulty and report it
    3. Use it with care for short jobs only
    4. Put it back in the store for someone else to find
    Show answer

    Answer: B. PUWER says work equipment must be kept in good repair, and the Management of Health and Safety at Work Regulations 1999 expect workers to report dangers. Taping over a crack hides the fault but does not make the tool safe. Label it, take it out of use and tell your supervisor.

    Source: PUWER 1998, regulation 5: Maintenance, Management of Health and Safety at Work Regulations 1999, regulation 14: Employees' duties · b10-003

  4. Who should use a power tool on site?

    1. Someone trained and authorised to use it
    2. Anyone who has used one at home before
    3. Anyone who has read the label on the tool
    4. Whoever is nearest when the job comes up
    Show answer

    Answer: A. PUWER requires people who use work equipment to have adequate training. Using a similar tool at home is not the same as being trained and authorised on site, where conditions and risks are different. If you have not been trained on a tool, ask your supervisor before using it.

    Source: PUWER 1998, regulation 9: Training · b10-004

  5. Why must guards be kept in place on power tools?

    1. To keep the motor cool and free of dirt
    2. To make the tool last longer between services
    3. To stop contact with dangerous moving parts
    4. To reduce the noise the tool makes in use
    Show answer

    Answer: C. PUWER requires measures, such as guards, to prevent contact with dangerous parts of machinery. A guard is there to protect you from blades, discs and other moving parts, not to protect the tool. Never remove or adjust a guard unless you are trained and the instructions allow it.

    Source: PUWER 1998, regulation 11: Dangerous parts of machinery · b10-005

  6. A workmate has taken the guard off a grinder because it gets in the way. What should you do?

    1. Use the grinder, but keep both hands well back from the disc
    2. Leave it, as it is their tool and their choice
    3. Tape the guard to the side so it does not get lost
    4. Tell them not to use it and report it to your supervisor
    Show answer

    Answer: D. The Health and Safety at Work etc. Act 1974 says no one may interfere with or misuse anything provided for safety, and PUWER requires guards on dangerous parts. Keeping your hands back does not protect you if the disc bursts. Stop the tool being used and report it.

    Source: Health and Safety at Work etc. Act 1974, section 8, PUWER 1998, regulation 11: Dangerous parts of machinery · b10-006

  7. Why should you not use a screwdriver to lever open a lid or cover?

    1. It is fine as long as the handle is not cracked
    2. It is fine if you wear gloves while doing it
    3. It is the wrong tool and can slip, bend or snap
    4. It only matters if the screwdriver is insulated
    Show answer

    Answer: C. PUWER says equipment must be suitable for the purpose it is used for. A screwdriver used as a lever can slip or break and cut your hand or send pieces flying. Gloves may reduce cuts but do not stop the tool failing, so get the right tool.

    Source: PUWER 1998, regulation 4: Suitability of work equipment · b10-007

  8. A lump hammer has a loose head. What should happen to it?

    1. It can still be used for light work only
    2. Soak the handle in water to tighten it, then use it
    3. Taken out of use until repaired or replaced
    4. Use it, but grip it close to the head
    Show answer

    Answer: C. A loose head can fly off and hit you or someone nearby. PUWER requires work equipment to be kept in good repair. Soaking the handle is a quick fix that does not last, so take the hammer out of use and get it properly repaired or replaced.

    Source: PUWER 1998, regulation 5: Maintenance · b10-008

  9. The striking end of a cold chisel has spread out into a mushroom shape. Why is this dangerous?

    1. Pieces can break off and fly into your eyes or skin
    2. It makes the chisel bite too deeply into the material
    3. It means the chisel is the wrong size for the job
    4. It makes the chisel too heavy to hold safely
    Show answer

    Answer: A. When a chisel head mushrooms, sharp edges can break off when struck and fly out like shrapnel. PUWER requires tools to be kept in good repair, so the head should be dressed by a competent person or the chisel replaced. Report it to your supervisor rather than carrying on.

    Source: PUWER 1998, regulation 5: Maintenance · b10-009

Related guides

Sources

General information, not legal advice. CITB and CSCS rules and prices change, so check their pages before you book or apply. SiteSide is independent and not affiliated with CITB, CSCS or HSE.